How to Build a Ramp Using BMX Ramp Plans

Materials Needed:.3/8" X 4' X 8' sheets of plywood
8' 2x4's
electric, handheld or bench saws
handsaw
hammer & nails
electric sander/sandpaper
drafting compass
string & chalk
garden hose
sawhorses
nail punch
ink pen
wood screws
3/8" PVC pipe
pushpin.1) Decide on the type of ramp(s) you want to build, sketch out the design and dimensions on paper.2) Acquire the materials required, and as much wood as you can get your hands on.

3) Find a work space to use (garage, backyard, etc.) and lay out your supplies. If you're planning to build a fairly large structure (permanent) try to build it on site.4) For ramps with curved transitions, you will need to use the string-and-compass method*.5) Once you've drawn and cut your templates, next comes the bracing.

6) Once you've done the framework, you'll most likely need to prep the top piece(s) of the plywood (which must bend to fit the transition without breaking). Do this by propping up the sheet(s)--already cut to size--at a sloping angle and soak with a hose at low pressure for an hour or so.As the wood becomes soaked, apply an increasing amount of weight to the center of the board(s)--using bricks or something similar--until the wood attains the desired curve.

Now nail the wood onto the framework's 2x4's If your ramp is to have coping, make sure to leave enough space for it to fit snugly. Always go WITH the grain of the wood while bending and apply the ply!.For a smoother transition, sand the bottom edge of the top sheet at an angle flush with the ground. Check for jagged splinters.

Sand or paint if desired. Paint will make your ramp faster! Duct tape, airplane or electrical tape or aluminum strips may be added to smooth the transition's bottom edge.* String and Compass Method.Figure how much transition curve you want (in feet & inches) and how much 'vert, if any. Tie one end of the string around the pushpin and stick it in the sheet as shown.

Holding the string taught, measure out exactly the amount of transition and mark this on the string with an ink pen. Tie the drafting compass to the other end of the string and tighten it so the slipknot is right on top of the mark you made. Holding the string taut, swing the compass from the sheet's edge in a quarter-circle, marking the template with the chalk. You may need to move the contraption around to get the desired curve and best use of space! Place sheet on sawhorses and cut out templates carefully.

NEW ADDITION ON DECREASING TRANSITIONS:.If you want to make a ramp with a decreasing transition, you need to modify the above steps and instead of using a pushpin, use a round object that is 6 inches to 3 feet in diameter, such as a paint can or a round garbage can. Attach the string to the round object and somehow secure it to the wood in place of the pushpin.As the string winds around the round object, it will get shorter and your transition will become tighter. This is called a decreasing radius transition and it is very cool when making launch ramps and quarter pipes.

.

Daniel J Lesser is the creator of BikeChoices.com Assembled by BMX and mountain bike "experts," you'll find every bit of information you could ever need about BMX and Mountain Bikes. Find out how to best enjoy your next ride at http://www.bikechoices.com.

By: Daniel Lesser



Baseball World






Cleveland Cavaliers Best in the East - The Cleveland Cavaliers have been proclaimed by many to be the next NBA champions after their signings of Larry Hughes, Donyell Marshall, and Zydrunas Ilgauskas.

Snow Bored - There's definitely a freedom in flying at high speeds down a hill through fresh powder snow, the cold wind threatening your face with minor frostbite, and your feet strapped to a few sticks of wood.

Hockey Rules Made Easy - If you're a newcomer to the game of hockey you may find the rules of the game a bit confusing, but with a little self-educating you'll pick up them right away.

Snowboard Stance - When you?ve purchased you?re snowboard, you are going to want to determine what stance you will use.

First undrafted quarterback to be elected into the Hall of Fame - Warren Moon kept himself a busy schedule after high school he played at a junior college in Los Angeles and in the Canadian Football League before reaching the NFL.

more...